Utility for formatting a flash drive kingston datatraveler 2.0. Methods for restoring a Kingston flash drive: from simple to complex. Using a program to recover a Kingston flash drive

Kingston flash drives are renowned for their reliability and long term services, but they are also not protected from various failures. Sometimes the drive actually “dies” and it is not possible to restore it. More often there are situations when a flash drive can be brought back to life using a special firmware utility.

Most often they break Kingston flash drives dt100g2 and datatraveler.

Is it possible to recover a flash drive?

Signs that the drive can be restored:

  • When you connect a flash drive, a notification appears that a new device has been detected.
  • The system prompts you to format the removable disk.
  • The drive does not open, but is shown in Explorer.
  • Errors occur when reading and writing data.

These problems can be eliminated by flashing the controller or formatting the media, but if the flash drive has important information, then before performing any restoration procedures you need to try to “pull it out”. Use to extract a recovery program like Recuva or so as not to lose the necessary files.

Search for a program for flashing the controller

To restore, you will need a special utility for a Kingston flash drive. In order not to make a mistake and download the right program, you need to know the drive controller model.

Method 1

Look necessary information You can go to flashboot.ru in the iFlash section, using the VID and PID values ​​of the flash drive as a filter.

  1. Connect the drive to your computer.
  2. Open Device Manager ( right click on the “Computer” icon - Management).
  3. Find "USB Mass Storage Device".
  4. Right click and open properties.
  5. Go to the Details section and select the Hardware ID property.

Method 2

Another way to get the information you need is to download the program Flash Drive Information Extractor and click the “Get Data” button. The report will contain the lines “VID” and “PID”; use their value to find a utility that can correctly restore the Kingston Datatraveler flash drive.


You can download the program in the “Files” section on the website flashboot.ru. If the utility is not here, try to find it on other web resources.

Recovery utilities

You can find the program you need without a controller model - just type in the search engine the request “kingston recovery utility”. In the results you will see several utilities, among which there will certainly be programs such as Phison Preformat, AlcorMP AU698x RT, etc.

The problem is that Kingston flash drive recovery programs only work if they are compatible with the controller installed in the drive. Therefore, if you download the first repair utility you come across, it may not detect the connected media.

When the desired program is found, you can begin to restore it. Be sure to look at the instructions, which should be packaged in the archive along with the recovery utility - perhaps the program has a special operating procedure. The general recovery procedure looks like this:


You don’t need to do anything else: the program will automatically correct errors and return the flash drive to a working state. This completes the restoration of the Kingston flash drive; if the controller firmware did not help fix the problem, then the reason incorrect operation It is worth looking among hardware faults.

Introducing programs for reliable formatting of flash drives

In this article we will look at the following question: which program to choose for formatting flash drives. Nowadays, flash drives of various types are used everywhere.

ATTENTION! We highly recommend reading the note about cleaning laptops. This is one of the main problems of beech trees breaking as a result of overheating! If all the heated air does not escape from the beech, do you think the internal parts could burn out from the elevated temperature? Of course yes, that is why this issue needs to be known very well.

Let's get down to business...

Introduction

In terms of convenience and speed of operation (in moving information), you cannot find a device better than a flash drive. But like any device, a flash drive can fail, that is, break. Their breakdowns are different.

For example, if it is a mechanical malfunction, such as a flash drive fell on the floor and became unreadable, or the flash drive was in water, and so on. Such breakdowns usually cannot even be repaired, unless they undergo specialized repairs.

But since the prices for them are now very low, repairing them in a specialized service is not profitable, unless the flash drive contained very important data, which can often be recovered.

From this we can conclude that a flash drive is a fairly fragile device and careless use of it can lead to its breakdown and loss of all data on it.

Formatting a flash drive

But it also happens that a flash drive just needs to be formatted in order to improve its performance or change file system, install ntfs or fat32. This can of course be done in a standard way in the operating system ( go to my computer - right-click on the flash drive "properties" - format), but this doesn't always help.

But in this case, there are many different programs that help not only change the file system but also bring the flash drive back to “life” or improve its speed. We will analyze these programs in this article.

This advice is that if you decide to find a program for formatting a flash drive, then it is advisable to use the same one as the manufacturer of the flash drive. For example, if you have a Kingston company, then it is advisable to select a utility for Kingston flash drives, but this is only possible, if not or don’t want to bother searching, then just use the ones presented below.

But this is not always possible to do, so you can completely use drives that are universal for all types of drives.

Let's move on to downloading programs for formatting a flash drive - we present below the 2 most effective and popular

The first program we will analyze will be HP USB Disk Storage Format Tool. Very good tool to fulfill our goal.

You can also download it from the official website. The program can be downloaded from this link http://www.teryra.com/articl_comp/kak_otformatirovat_fleshky/HPUSBFW.ZIP (copy, paste into the browser and press enter). There is no need to install the program, just run it.

It is packaged in an archive; in order to run it, you may need an archiver; in general, this is a standard program; how and where you can download it, see the article on how to open a rar file.

And so, HP USB Disk Storage Format Tool program very easy to use. All you need is:

  1. Launch it
  2. Indicate your flash drive in the first line
  3. Next, specify the file system, preferably NTFS, although FAT32 is also possible
  4. And put a tick in the Quick Format line. There is a small nuance here. If you just need to change the file system, for example from FAT32 to NTFS, then check the box. A tick indicates that formatting will be quick. If we need to correct the incorrect operation of the flash drive or it is impossible to write files to it at all, then we do not check the box. This means that the formatting will be complete. With full formatting speaking in simple language, some errors that have accumulated on the flash drive are corrected and perhaps after this process it will work better.

Don't forget that formatting deletes all information from the flash drive, so copy it if there is anything important

If everything is specified, then click “Start”:

The following program is hdd low level format tool

To download it, click here:

Install hdd low level format tool

The installation process is standard, click next and next everywhere, only click “Accept” in the license agreement window.

The entire program is installed, the only thing is that it is paid and when you start it a window will appear asking you to pay or use limited time. But it will be enough for us to perform several operations.

If you don't want to pay, then choose trial version, that is, click the bottom line “Continue for free”:

The program looks like the figure below. In our case, as we see, the program has identified two devices, these are HDD at 1.5 Tr. and a 16 GB flash drive:

How hdd low level format tool works

This program approaches the formatting process more thoroughly. She spends low level formatting(as stated, although there is an opinion that this process can only be started in factory conditions, but we still try).

During this formatting, sectors are edited and bad zones are eliminated. Can show technical condition hard drive(only for hard drives), to do this, in the initial device selection window, select your hard drive and click “Continue”, and then go to the S.M.A.R.T. tab. and click on the “Get Smart Data” button:

In order to format a flash drive, select it in the initial window ( ATTENTION! WE ARE VERY CAREFUL HERE, WE CHOOSE Slowly, Otherwise, you will format your hard drive and lose all the data accumulated over a long time), click “Continue”:

In the next window, go to the LOW-LEVEL FORMAT tab and click on “Format This Device” at the bottom. The low-level formatting process will begin and will take from 40 minutes to several hours:

This program often helps to cope with a problem such as a flash drive that has stopped being read or has started to work slowly. It is very important to do everything slowly and thoughtfully. If you doubt something, it is better to ask someone again than to later regret hasty actions.

So we looked at such an interesting and popular question as a program for formatting flash drives. This is very helpful information. Thanks to it, in many cases you can save a flash drive from emerging problems.

Many users encounter problems when a USB drive (flash drive) fails, and even such a reliable company as Kingston is no exception. Symptoms that the drive has failed, but it can still be saved are the following:

Problems when writing or reading data from a flash drive to a computer, freezing, crashes;

The flash drive appeared in Explorer, or any file manager, but it is impossible to open it, it produces various error messages;

When you connect a drive, the operating system always prompts you to format it (even after the formatting procedure has been completed);

When connecting to a PC, the system displays a message about finding a new device, but it doesn’t go any further;


To restore the flash drive, you need special utilities for Kingston. To make the right choice, you need to know the controller model; we need information about the VID and PID of the flash drive (unique identifiers). You can find them out using the operating system, or by downloading and installing the Flash Drive Information Extractor program.

First way. We connect the USB drive, call context menu my computer and go to “Management”, select “Device Manager” in the list of “USB controllers”, find “Storage USB device", in which we also open the context menu and select "Properties". In the properties you need to select the “Details” tab and select “Equipment ID” from the drop-down list. This way we will get the information we need.

Another way is to get the data using Flash programs Drive Information Extractor, after installing it, connect the USB drive and click on the “Get data” button in the program.

Next, you need to use specialized sites to search for the necessary recovery programs (flashboot.ru is popular among them). In one of the sections, namely iFlash, by entering previously received data about VID and Drive PID we will receive information that the utility should search for and download.

If you have a Kingston flash drive with a size of 8, 16 or 32 gigabytes, then the list of programs for their resuscitation will include the following utilities:
Phison Preformat;
AlcorMP AU698x RT;

After downloading the desired program, install it on your Personal Computer and launch. We connect the failed USB drive; if it appears in the program window, then it is selected correctly. All you have to do is select it and click on the “Start” button. The utility will correct all errors automatically. Disconnect the flash drive and check the result.

Before talking about the repair of USB flash drives from the American company Kingston, it is worth mentioning a couple of significant facts about this company, which is the undoubted leader in the supply of USB drives, second in the world in the production of flash memory and third in memory cards.

The Californian company Kingston was founded on October 17, 1987, but although the company is American, its origins were from Taiwan, John Tu and David Sun. Kingston Technology currently ranks 77th on Forbes' list of the 500 Largest Private Companies in the United States.

A huge variety of flash drives in shape, color, case material, as well as volume, from the smallest to 1 TB. There are series of drives with data encryption that are suitable for corporate use that requires a high degree of protection and encryption of information.

All Kingston USB flash drives are covered by a warranty that guarantees the exchange of a faulty device if the breakdown is not the fault of the buyer. The minimum warranty period is 1 year; there are lines of flash drives and memory cards for which the warranty is valid for up to five years. As a rule, no breakdowns occur in the first years of use. Repairs are often required after warranty service and, despite the high reliability of this company’s products, no one guarantees that one day your drive will stop working.

If your storage device is no longer detected correctly, shows zero or incorrect capacity, asks you to insert a disk, etc., then this indicates a software failure at the controller level. These and other similar faults can be repaired. There are several programs for repairing Kingston flash drives, not counting universal utilities. Let's look at a few of them so you know how to work with them. Download the archive containing all three utilities from the link.

Phison Preformat v.1.30

The program helps restore flash drives on Phison controllers, which are also used by Kingston. Run it with the file preformat.exe, if it displays the message: Preformat does not support this IC, then the controller is not supported. If the program starts, a window will open, as in the image below, where you are given four options: full formatting, fast, fast low-level and full low-level.

No instructions for use are needed. Select modes one by one and check the drive. Remember that after a quick and complete low-level formatting, it will be impossible to recover the information that was stored on it, so take care of this in advance.

Another very simple utility that can help fix errors. Everything is simple, if it starts, then the device is assembled on a controller compatible with it. There are only two buttons: Format and Cancel. The first is low-level formatting, which helps to repair the device in case of logical failures, and the second is to close the utility.

A production utility that has managed to bring many flash drives back to life. The instructions are simple: run the AlcorMP.exe file, if your drive is detected in Device Status, then click Start and check its functionality.

These three programs for repairing flash drives from the manufacturer Kingston can “cure” most devices. If the universal utilities for diagnostics and recovery provided on the site.

Kingston Format Utility is a simple utility that is designed to format USB drives. Allows you to format devices from the manufacturer Kingston; to do this, you must first select the file system. This useful program, which will be useful to all owners of flash drives from this manufacturer. Allows you not only to format the drive, but also to correct existing errors in the system.

Kingston is a large company that produces USB flash drives for PCs and laptops. At first, manufacturers wanted to create a program for HyperX series flash drives, but they soon changed their minds and made the program more universal by including Kingston products.

The application has an important advantage: devices are formatted using high speeds, which cannot be said about other similar programs. And also a standard formatting program cannot compare. Kingston Format Utility supports the robot on PCs and laptops with operating system Windows, various versions.

Another feature is the function of converting the file system from FAT32 to NTFS. Each of these systems has its positive and negative sides; it is worth understanding that FAT32 is intended for smaller files, but the second, on the contrary, for larger ones. Kingston Format Utility has a simple and user-friendly interface that any user can easily navigate. Before you start formatting, you need to select a specific drive and file system, which was mentioned above. The formatting process does not last more than 15 minutes. During this period, the user can go about his business, because there should not be any problems in the process.

Main features

  • Kingston Format Utility is a simple utility created for formatting flash drives;
  • Convenient interface that includes all the necessary functions;
  • Can change the file system from FAT32 to NTFS;
  • Works with USB drives from Kingston;
  • Takes up minimal free space on your hard drive;
  • Formats flash drives in a short period of time;
  • Distributed free of charge;
  • Finds and corrects errors in the system;
  • Can work on computers and laptops with the Windows operating system.