DIY tablet case made of leather. Is it possible to sew a protective tablet accessory at home? Making a leather case for a tablet

A tablet case is a necessary accessory for your electronic assistant! Our model is fastened with Velcro and additionally reinforced with plastic inserts. This case is suitable not only for a tablet, but also for an e-reader.

Tablet case: choosing material

How to sew a tablet case with your own hands? Our case is made of thick genuine leather with a bright cotton lining. Choose dense, abrasion-resistant materials: denim, corduroy, faux leather or suede. In order for a case for a tablet or book to hold its shape well and be used as a stand, it must be strengthened.

We used thin plastic from a folder for papers, the choice of which is huge in office supply stores. The plastic should be quite dense, about 0.7-0.8 mm thick. It can be cut with scissors and stitched with a machine needle (number 80-90). You can also use thick and rigid cardboard.

In order to connect layers of fabric and plastic, you will need adhesive material. This can be adhesive web, double-sided tape or transparent glue (fabric or leather should be indicated in the annotation). You can use one of these materials or all three. Glue web is convenient for gluing large fragments together, bending edges with tape and gluing small parts, and using glue to secure threads.

You will also need an elastic band and Velcro for fastening.

As an example, we sewed a cover for an e-reader, so it has a vertical format. The tablet is most often used in a horizontal position, so the case for it should open up and also be able to be installed on a table, along the long side. Please pay Special attention on the connectors and buttons located on the sides of some models - these places should be left open.

So, let's sew a case for your tablet or e-book with your own hands!

Uncover

Part B– corresponds to the size of a tablet or a book, maybe 3-5 mm larger

Part A– the same width as part B. The length is double the length of part A plus the thickness of the tablet or book and plus 1 cm.

Part C- the same width as part B. The length is slightly more than 1/3 of the length of part B.

Part F- fastenings. They may be triangular in shape if the device body has a wide frame. Each side of the part must be at least 1/3 the length of the side of part B to which it will be attached.

Part H– fastener of any shape. The length of the part should be 5-7 cm greater than the thickness of the tablet in order to close freely.

Leather

Part A 1 piece
Part C 1 piece
Part H 1 piece

From fabric

Part A 1 piece, can be shorter by 5-7cm
Part B 1 piece
Part F 4 pcs, 2 in one direction, two in the other
Part H 1 piece

Made of plastic

Part A 1 pc. Reduce length by 5-7 cm and cut into 5 pieces. In order to place the cover at different angles, you need 3 parts, 2 x 2 cm wide and 1 – 4 cm wide. It is better to determine the length of the remaining two parts during sewing.
Part B 1 piece
Part C 1 piece
Part F 4 pcs
Part H 1 piece

Cut out fabric and leather parts with a 1 cm allowance. F leather parts can be cut without allowances, depending on the thickness of the leather and its cut. Cut out plastic parts without allowances.

Progress

parts made of leather, fabric and plastic
elastic band, velcro
adhesive materials, threads

Glue the fabric to the plastic using spider web, double-sided tape or glue.

Sew Velcro onto the glued part of the fastener. Fold and glue the edges onto the leather clasp.

Try on one pair of mounts by inserting a tablet or book. Pin the elastic bands to the fabric.

Fold and glue the edges of leather piece A. Sew the second part of the Velcro fastener on one side.

Fold the detail with the pinned pair of fasteners and the leather detail with the sewn-on clasp, wrong sides inward. Sew along the short side, turning the corners slightly.

Sew fasteners on the second side, starting stitching about 1/3 of the total length of part B.

Fold the leather part A and the fabric part A with the plastic glued on wrong sides inside. Insert the fastener detail from the free edge as shown in the photo and stitch along the edge until it intersects with the stitching near the fasteners.

Tuck and glue the edges along the 3 m sides of the leather on the plastic-reinforced part C.

Tuck the free short edge of the fabric inside the cover. Hand-sew where all three parts join. Sew horizontally near the attachment point just below the end of the plastic in part C.

Recently, tablets have become very popular. They greatly simplify our life, and also make it more convenient and interesting. But, unfortunately, tablets often get scratched, which ruins their appearance. That's why it's so important to use cases for tablets. However, not everyone has the opportunity to purchase a suitable case. There is a way out of this situation. You can make your own tablet case yourself. What do you need to have with you and how to make a tablet case with your own hands? This is exactly what we will discuss in detail.

If you still don’t know how you can make a case for your tablet yourself. Or maybe you don’t even know if this is possible? Let us tell you right away that such things can not only be made with your own hands, but their appearance will be no worse, and maybe even better, than purchased covers. In addition, you can use all your efforts, turn on your maximum imagination and take into account your preferences. All this taken together will help you achieve a wonderful original result. Now let’s move on to our tutorial on making a tablet case with your own hands.

How to sew a tablet case

To sew a book case for an iPad or Samsung tablet yourself, you actually need to have a little free time and put in a little effort. It goes without saying that you have the opportunity to create a real masterpiece, which, in addition to its direct purposes, will also “delight your eye.” And yet, what is needed to sew an original case for a tablet? Below is the first version of a case made by yourself.

Before you start, prepare:

felt (colored). Cut it to fit the size of your existing tablet;
button;
2 cardboards. Also cut to the size of the tablet;
rubber. To secure the tablet in the case
glue;
Let's get straight to work.

Before you sew a tablet case yourself, please note that if you do not have felt, you can replace it with another suitable fabric. It could even be leather or leather substitutes. In general, you can use whatever you want. Now let's start with the work plan.
Glue a correspondingly sized piece of leather or other material of your choice onto each cardboard. Make sure that between these cardboards there is short distance. This is necessary so that you can easily close the case in the future. That is, make a case for your tablet like a book.

We sew a case for your tablet yourself

Next, take the edges of the remaining fabric and fold them inward. Now glue them to the cardboard. Glue the leather strips to the bottom. They should be 15 cm long and 1 cm wide. Cut these two strips into two even parts and attach them to the corners of the future cover using glue.

We sew a cover with our own hands

It is important to check how your tablet is “placed”. Next, glue 2 rubber bands to secure the tablet. The main work is already behind us.

Then, cut out a small piece of leather (or the same fabric) that will be slightly smaller in size than the tablet. Glue it inside. This is done in order to hide the cardboard, that is, to make the cover beautiful to look at. Sew all this carefully so that nothing comes apart or comes unglued.

In the end, all that remains is to make the fastener for the case. You will need a small piece of leather or fabric, as well as Velcro. On one side you need to glue a piece of leather (fabric), and on the other - Velcro. This way, you can close your case easily. Carefully sew it all on top. This way you will secure the result. This is all. Now you know how to sew a case for your tablet.

As you can see for yourself, there is nothing complicated here. And making a case for your tablet yourself is easy!

You can take a regular phone case as a sample. And then, using your imagination, make a similar model, but in slightly larger sizes.

Original tablet case

Anyone can sew an original tablet case with their own hands. But it remains important how he will do it. We will not dwell on one option. We'll show you another way to sew an original tablet case.

This method may surprise many, but, in any case, it is an excellent solution.

To work you will need the following items:

an unnecessary old book (it should be a little larger in size than your tablet);
brush;
ruler;
glue;
knife (clerical);
any heavy object.

Let's take a closer look at how to make a case or cover for a tablet from an old book. After choosing a suitable book, apply glue to its edges. Then leave this book for about 1-2 hours. This is done to allow the glue to dry completely. Now, take a ruler, open your book and mark the dimensions of the notch (according to your tablet). After that, cut out the pages.

All work has already been done. Your tablet case is ready.

DIY tablet case

You can make your own tablet case with your own hands using the first method, but add some original ideas. For example, you can place foam rubber on the outside between cardboard and fabric. This way you will make the case much softer.

You can decorate the case using various available materials. As an option, you can sew a case in the form of a clutch handbag, but just take into account the size of your tablet. Regarding fabrics, you can choose any you like - depending on your wishes and preferences.

And to put it another way, there are no restrictions in creating a case for your tablet. You can even come up with some interesting way to create your own iPad bag. And perhaps this method will exceed all your expectations and will be very popular.

Please note that iPad case clasps may also vary. You can use Velcro or magnets. But, with the second option, you will need to glue magnets inside at the beginning of work. They will fix 2 sides of the cover when closing it. You can also learn from us about DIY furniture.

Nowadays you can find a variety of accessories and supplies that will help you in any job. But a DIY tablet case you create will always attract people around you. And, you can be completely sure that you will not see a similar case anywhere else. Such an original creation will be valued much more than a regular case bought in a store. I wish you creative achievements and success. Never stop there.

Video on how to make a case for an iPad

In modern society, new technologies have long appeared that require protection and cleanliness. It’s quite easy to deal with cleanliness, but you need to think about strong protection, because if our new tablet If it breaks on the first day of use, we will not be very pleased and even offended. But not always enough Money to buy not only a tablet from a good company, but also special accessories for it. In this article you will learn how to make a case for your favorite tablet quickly and easily with your own hands.

Basically the ideas are quite original and simple. If at first glance it seems to you that the manufacturing instructions are complicated and require unnecessary materials, do not worry. Read the instructions again and you will understand that there is nothing complicated here, and the materials can be replaced with others that are more to your liking.

You can, of course, buy a protective agent, but at a low price it is unlikely to last long. There are also high-quality, expensive models, but a case you make yourself will be much cheaper. After all, although it will require costs, they will not be so large. And you will also know exactly what it consists of and how it is made.

Let's understand the main types of tablet cases made by yourself

A simple and interesting option made from felt

The simplest method that will not only protect the device from damage, but also retain heat.

For it you will need:

a piece of felt;
Needle;
Dense threads;
Scissors;
Ruler.

Let's start production:

To begin, take felt and mark two identical contours on it (the size of the tablet plus two centimeters on the sides). Cut carefully, without touching anything unnecessary, along the intended line, then sew: right side, bottom and left side. That's it, the cute little case is ready. You can decorate it with beads, quilling, sew it with colored threads, or draw a picture with paints.

Trying to create a stylish denim case

In addition to ordinary fabrics, if you show your imagination, you can use something more interesting.

For example, below is an option on how to make a case for a tablet from jeans . This look will look much more interesting and attractive than felt.

You can immediately go looking for old unwanted denim trousers, because this method will definitely attract your attention.

For it you will need:

Jeans;
Needle;
Threads;
Awl;
Cardboard;
Lock.

Let's start production:

Cut off the top back, according to the size of the tablet, to make a book. Glue cardboard onto the inside. Use an awl to make holes in the sides (don't touch the top!), then sew the sides together. If desired, you can sew a lock on top to prevent the device from falling out. And, of course, decorate with decor.

Ready! Now you have not only a case for tablet computer, but also two pockets for small items.

Elegant leather case for all times

Well, besides fabrics, leather has always been and will remain the most elegant. Consider the following option for a protective and attractive case.

For it you will need:

Leather cloth;
Strong cardboard;
Non-slip fabric;
Glue (preferably transparent);
Needle;
Strong threads;
Scissors;
Pencil or pen;
Ruler;
A pair of rubber bands;
Awl;
Plastic;
A piece of soap or remnant.

Let's start production:

We cut out two identical parts from cardboard, measuring the dimensions of the tablet and adding one centimeter - this will be the base. Using scissors, round two corners. Use a ruler to divide one of the parts into two parts. Then cut a line of 0.5 centimeters.

We glue the three finished parts onto plastic. Next, we iron the fabric well and glue the parts to its wrong side so that the plastic is at the top. This is done as follows: first glue the largest part, with rounded corners to the left, mark the top and bottom stripes with soap (so that the remaining parts go smoothly), retreating 1.5 centimeters, glue the part with right angles and, retreating another 0.3 centimeters, glue the remaining part, rounded corners to the right.

Leaving one centimeter at the edges, carefully cut the fabric. We wrap the edges and glue them inside. We glue elastic bands to the large part at the corners, and sew leather fabric on the outside. We attach a clip on top that will hold the case itself when it is in a standing position.

Now you know that sewing a leather tablet case is not difficult, you just need some additional funds.

At first glance, it seems that these ideas are completely unoriginal and useless. But you shouldn’t judge it without trying it. First try to make all these three types, the result will definitely pleasantly surprise you. And even if you don’t like it, knowing already some options, you can come up with instructions yourself, using your imagination.

Happy crafting and pleasant surprises!

Video materials on the topic of the article

And if you are not at all interested in these ideas, please pay attention to the video selection. Perhaps you will like something there, and you will definitely try it.

The age of new technologies is coming. Almost every day new models of smartphones, phones, and tablets are invented and released into the world. All these things are in demand and in many cases necessary for a modern resident of a metropolis.

Every person who has bought a brand new, long-awaited model of phone or tablet strives to keep it safe and sound.

In order not to break or scratch your equipment again, special accessories are purchased in stores in the form protective films, trinkets rubbing, covers. Many of these things are quite inexpensive, and some can cost you the price of a brand new handbag.

But there is always an excellent low-budget solution - these are accessories made with your own hands, that is, hand-made.

In this article I will tell you how to make a real book-shaped tablet case from an old bag, cardboard and a couple of scraps.

For the case you will need:

- cardboard
- scissors
- artificial or genuine leather (I took the top of an old bag)
- fabric for lining (it’s better to take thick fabric, not slippery, I use velor)
- glue “Moment”
- Super glue
- hot glue gun
- elastic band, black
- Velcro

I made this book case for my tablet in just an hour and a half. The cover was needed urgently. And in order not to waste money, I decided to make it myself.

I had an unnecessary bag that I only carried for a month, after which its lock broke. It was a shame to throw it away, and I simply put it aside until better times, that is, until I get around to fixing this unfortunate lock. But my hands didn’t get around to it the whole winter, and the bag hung and collected dust on the hanger.

I never thought that I would ever decide to reshape it and make a case for a tablet. But when I thought about what kind of cover to make for the cover book, I immediately remembered that very handbag.

Then I measured to see if the side of the bag would fit. Everything was fine, so I cut it into a suitable rectangle. Then I found a couple of scraps for the lining. I took glue, a heat gun, an elastic band, scissors and cardboard.

I’ll immediately make a reservation about cardboard. It is better to take cardboard that is dense, not brittle and not thick. Unfortunately, my cardboard turned out to be quite thick, so the cover turned out to be not very thin.

One more moment. If you have thin plastic, you can use that. I think it will be even better, because it will not get wet in water and the cover can be washed.

Well, I think I’m done with the introductory part, now I’ll tell you how to make this little case.

First, I traced the tablet using a pencil on cardboard.

I cut out two identical pieces from cardboard.

I covered the cardboard with pieces of fabric, folding the edges of the fabric to the inside.

Then I took a black elastic band and made holders out of it for the corners of the cardboard lining.

I glued both linings to a piece of faux leather cut from an old bag, leaving a distance between them equal to the thickness of the tablet.

After that, I trimmed the cover to the required size and, bending the corners, placed them on glue.

I made a clasp from the fastening part of the handle, gluing Velcro to the edge and placing the strap spine on super glue.

To keep your favorite gadgets looking presentable for as long as possible, you should put covers on them. Yes, in some stores their prices are very high, but it is not at all necessary to make such a purchase. You can make a tablet case with your own hands from any fabric, even jeans. You will get a beautiful cover that will preserve your favorite gadget for a long time.

Sewing a cover for a tablet from felt means decorating it beautifully, because this material has a fairly bright color. For this work you need to prepare the following materials:

Felt. It is recommended to use contrasting colors.
Duct tape. As alternative option it can be replaced with double-sided tape.
Textile. Preferably cotton.
Scissors and thread.
Needle.

Sewing instructions:

First you need to measure the parameters of the gadget. This is necessary in order to know how much fabric to cut. After this, 2 pieces of equal size are cut out of felt. You should also cut out 2 pieces of fabric.
Now the felt and cotton fabric are placed right side together. On sewing machine You should make an even seam running from top to bottom.
Then the stitched seam should be ironed. It should be ironed towards the gasket. Now both parts are folded, you need to iron them.
After this you need to make a valve for the cover. To do this, a rectangle is cut out of felt, the length of which is no more than 20 cm. It should be folded in half and stitched using a finishing method.
Velcro or double-sided tape is attached to the inside of the valve. The part is attached to the case. The valve must be firmly sewn to the product, otherwise it will fall off.

Gallery: DIY tablet case (25 photos)

How to make a leather tablet case with your own hands?

Sewing a leather case is not difficult, and besides, such a product looks very elegant. A homemade leather case is made according to the following scheme:

The first step is to measure the gadget. After this, you can cut a piece of leather to the desired size. It is important to take into account the curly edge. After this, another leather piece is cut out.

Now the skin should be treated with water. You can use a spray bottle for this.
A pattern is made from two blanks. Each piece must be cut according to the original measurements. You should use a measuring tape at this stage.
To sew patterns, you need to use an awl. Using an awl, holes are made at the edges of the workpieces through which the thread will be threaded.
If the leather is too thick and difficult to pierce with an awl, then you should place the tool perpendicular to the coating and hit its top with a hammer. Thanks to this maneuver, the awl will pierce the skin.

Tip: To give the leather cover its shape, it should be moistened with water and put on the gadget.

Tablet cover made of fabric: how to make?

A fabric cover is the easiest to make. This product wears out quickly, but is easy to replace with a new one. So, instructions for working on a fabric cover for a tablet:

To make a durable fabric cover, you need to use cardboard when creating it. Measurements are taken from the gadget, you need to determine its length and width.
Based on the measurements, 3 cardboard pieces are cut out, 2 of which must correspond to them. The central piece of cardboard is the thinnest, it is placed in the center between two large pieces.
Now you should cut out the corners of the cardboard blanks so that the cover has rounded edges.
The workpiece is placed on the fabric. The fabric must be cut out after outlining the edges. After this, the action is repeated to cut out another piece of fabric.
Two flaps are attached along the wrong side so that the gadget can be inserted into them. That is, one side should not be stitched.
After the case has been put on the tablet, the unexpired side can be sewn up.
If the craftsman wants to secure the gadget more firmly in a homemade fabric case, he can attach a loop of tape to the case.

Book case for tablet

A book case is the most practical cover for a gadget that you can make. With it, the tablet can be used as a TV. The book cover is made according to the following scheme:

At the first stage, the parameters of the device are measured, or rather its width and length. After this, 0.5 cm is added to these two indicators for more accurate work.
Lightning is taken. A ribbon should be sewn to its edge. The workpiece is put aside for now.
Now take the book. It must be large enough to accommodate the tablet. Pages are cut out of the book.
Now the book cover without sheets inside unfolds. Using an awl, you should make holes along its edges, 1 cm apart from them.
Starting from the spine of the book, you need to sew on a zipper. For convenience, the zipper is sewn in the center of the product. This will make it easier to take out the tablet.
Now another zipper with tape is sewn to the sash.
If desired, you can attach a cardboard leg covered with fabric to the back of the case.

Homemade tablet case made from jeans

The jeans case looks very nice. To do it, you need to follow this plan:

In addition to old unwanted jeans, you need to prepare cardboard. You should measure the parameters of the gadget to know how much denim material will be needed for sewing.
To make your work easier, you can attach the gadget to the cardboard and trace it, clearly marking the top and bottom. After this, you can attach the cardboard cut along the contour and cut out the denim material. You need to cut it taking into account 2 cm on the side turns.
The denim seam should be in the center of the fold of the future cover.
Now the material can be folded on the sides. To fasten the denim material, you can use instant glue.
The outer side of the cover should be well ironed.
You need to attach elastic bands to the edges of the inside of the case so that the tablet is firmly attached to them inside. They are carefully sewn in the center along 4 edges. At this stage, you need to determine whether the gadget fits well in the product; if not, then it is worth correcting some previously made mistakes.
If the gadget fits well in the case, you should take it out to complete the work. The edges of the denim cover need to be stitched using a typewriter. If desired, you can use a bright, eye-catching thread for stitching.
Also, the stitching should be done at the folds of the case.

How to decorate a tablet case?

A homemade case can be decorated in different ways. Its design is not necessary, but it will make the item look much better. So, the main ways to decorate a homemade tablet:

Sew the edges of the case with thread using a sewing machine.
Make a creative fastening, for example, use a chain as a fastener.
Sew buttons of different colors and sizes onto the surface of the cover.
Decorate the product with satin ribbons.
Place stickers on the case with happy wishes to the owner of the gadget, etc.

There are really a lot of ideas for creating homemade cases for gadgets. With such a product, your favorite tablet will serve its owner much longer, because it will be protected and decorated.