Not configurable 1. How to set up DVB-T2 digital television. Automatic channel tuning on TV


Widespread modern television there was a stir, and therefore a lot of questions, how to setup digital television . The reason for its popularity is the variety of channels in terms of direction, quality, language, type of content, etc. Due to the lack of information on setting up digital TV, companies have appeared like mushrooms after rain, charging fees for these manipulations. You don’t have to pay at all, you can actually achieve the goal on your own.

How to set up digital television on a TV - general provisions

Mostly all methods for setting up digital television reception use approximately the same scheme, but due to the variety of manufacturers, the actions may be slightly different, but their logic is similar. In order not to get confused in all the sequences, it is worth applying the algorithm directly to each TV model. Thanks to logic and intuition, you can correctly configure the settings on almost every TV model using the instructions provided.

  1. Take the remote control and expand the menu;
  2. Proceed to the “Options” item;

  1. Next, you need to activate “Auto Configuration”. With this action, a window appears containing information about the signal sources; it can be a cable or antenna signal. In our case, we need to select a cable;
  2. At the end of the operation, information about the quality of signal reception should appear in a new window, here you should select “Digital”, then click “Start”;
  3. The final setting point is “Search mode” and select the method for detecting channels. The proposed fields must be filled in with information. The frequency is 314 MHz, the speed is 6875 kS/s, and the modulation is 256 QAM.

More advanced TV models allow you to perform a network search, which will independently perform all the necessary actions. When the desired method for detecting TV channels is selected, you need to click on “Search”.

If this instruction is not effective, you should use a detailed algorithm for LG TVs. The technique is relevant for almost all models of the manufacturer.

  1. From the remote control go to the Menu;
  2. Click on “Options”;
  3. In the “Country” category, change the checkbox to Finland or Sweden;

  1. Then go to the “Settings” category and launch “Autosearch”;
  2. In the fields you need to enter a search method, usually a fairly fast type, frequency - 298 MHz, modulation - 256 QAM, characters - 6952, ID - auto;
  3. If everything is done correctly, then during the search a number of TV channels will be displayed;
  4. Manufacturer LG integrates into the system automatic system search and update TV channels. This function can be inconvenient as the prepared list will be reset regularly. To prevent this phenomenon, be sure to go to the settings for connecting via cable and turn off “Auto channel update”;

  1. For convenient sorting, you need to remove the check mark from auto-numbering in the “Cable” section in “Autosearch”.

Now let’s look at the Samsung method, because the manufacturer is one of the most popular in the industry. The actions are like:

  1. Press Menu on the remote control;
  2. Next, go to the “Channel” category (there is a satellite dish on the icon);
  3. On the right you need to select the “Antenna” option, and in the type field - “Cable”;

  1. Now in the “Country” section you need to set “Other”, now you will need to enter a PIN code, by default 0000;

  1. Go to the “Auto-configuration” menu and specify the source of the signal – “Cable”;

  1. You need to specify the parameters, they correspond to the data in the first one, general example articles, and click “Search”;
  2. Now the TV will find all TV channels.

How to set up digital television on Smart TV

Let's look at digital television and how to set up channels on a TV with the Smart function using Samsung as an example. The action is performed fairly standardly, but there are some differences.

  1. Go to the “Channel” section in the Menu;

  1. Click on “Country”, you may now need to enter a PIN code, by default 0000, 1111 or 1234;
  2. Follow the "Other" section;
  3. Then, step back, select “Cable search options”;
  4. Standard parameters are now being introduced;

  1. Again you need to go to “Auto Configuration”, here select the “Cable” source mode;
  2. You need to activate the “Digital” section;
  3. Using the search mode, select “Network” and activate the setting.

All methods allow you to create a high-quality connection to digital TV channels and find the maximum available number of interesting programs. Despite the lack of data on devices from Toshiba, Philips and others, the connection method is no different.

If you have any questions about the topic " detailed instructions on setting up digital television", then you can ask them in the comments


if(function_exists("the_ratings")) ( the_ratings(); ) ?>

TV channel 1+1 and all channels of the 1+1 media group change broadcast parameters from the satellite. Or more precisely, they change the satellite and switch from AMOS-2 4 W to satellite ASTRA 4A 4.8 E.

TV channels 1+1, Unian, PlusPlus, Kvartal TV And Curlers already available from satellite ASTRA 4A 4.8 E and broadcast in test mode until December 12 (extended until March 1), and after that on an ongoing basis. But on Amos 1+1 will be available until February 15, 2017. Later, the media group's broadcasting will completely switch to Astra (formerly Sirius).

New satellite parameters and frequencies for tuning the 1+1 (1plus1) TV channel and the entire media group

Broadcast parameters 1+1

Satellite ASTRA 4A 4.8 E

Frequency – 11766 H 27500 3/4

11766 MHz, horizontal polarization, symbol rate 27500 Mbit/s, FEC–3/4, DVB-S/QPSK

The change of satellite and broadcast frequency is associated with the end of the satellite’s service life AMOS-2.

Some TV channels have already migrated or are currently broadcasting from two satellites.

You can also look at the broadcast parameters of previously migrated TV channels.

The information was officially confirmed by the executive director of the media holding and the 1+1 TV channel is already broadcasting a video about the change in satellite broadcasting.

StarLightMedia is moving to another frequency.

Also important news for TV channel viewers STB, ICTV, Novy channel, M1, M2, QTV which in 2017, from March 1, switch to a new frequency from the Amos 2 satellite to Amos 3. And thus remain on Amos.

New TV channel broadcast parameters STB, ICTV, Novy channel, M1, M2, QTV

Amos-3, 4W

11175 H 30000; 3/4

Also, all TV channels inform about changes in broadcast parameters from the satellite and many are sent via the link telemaster com ua (telemaster com ua). Where text and video instructions are provided for reconfiguring channels yourself or searching for a specialist in your region or locality.

If setting up channels is a difficult task for you, then it is better to contact a specialist. This will be more reliable and of better quality.

The easiest way to set up your TV is automatic mode when the TV itself searches for all the channels and arranges them sequentially and remembers them. When setting up your TV, automatic search may skip channels with too weak a signal.

Undesirable results may occur when automatically tuning your TV:

  • the TV can remember one channel of normal quality and another of the same quality, but with a lot of noise;
  • The TV itself may not determine the sound standard on some channels (there will be sound, but there will be no sound)

To eliminate unwanted auto search results, you can switch to manual TV setup mode and manually delete them. For example, “Menu”/“MENU” –> Channel settings/Channel –> “ Manual setting» (see the instructions for the TV). In the “Manual tuning” channel mode, you can manually change the audio broadcasting standard on those channels where there is only a picture.

Please note that everything The described steps are also suitable for setting up the TV to receive terrestrial digital television to an indoor antenna.

Detailed instructions for setting up your TV in pictures

To find the section for TV settings in the menu, refer to the TV's instructions. You need to find a menu with a line to start automatic channel search and start this procedure. Usually it is called up by pressing the “Menu” / “MENU” button -> Channel settings / Channel -> “Auto tuning”. The TV itself will clear the memory and record the channels present on the cable network.

If you are unable to set up your TV yourself, you can: on a paid basis at your home by phone.

How to set up a TV in automatic mode using the example of a Samsung Plano TV

Comment. The images below are photographs of the TV screen. The quality of the image taken by the camera is much worse than the real image on the TV screen due to the characteristics of the camera.

1. To enter the TV settings, press the MENU button on the remote control. Text with the names of sections of the TV menu will appear on the TV screen. To move up and down and left and right in the TV menu, use the arc-shaped buttons with the image of triangles, placed side by side in a circle (in the photo around the Enter button). To increase or decrease any parameter, use the volume + and - buttons. To exit a menu or return to the previous menu, use the button labeled TV or EXIT.

2. Once you enter the menu, you will be taken to the image settings section. To go to the settings of television channels, use the down-up buttons and scroll down until the phrase appears at the top Channel, and an icon depicting a satellite dish will be highlighted on the left.

3. Now go to the right side of the menu using the right arrow button. After this the phrase should be highlighted Auto-tuning.

4. To start auto-tuning, press the right arrow button again. Put the remote control aside and wait until the progress bar reaches 100%. This will take about 5 minutes. While scanning channels, the found channels will briefly appear and disappear on the screen and the channel number counter in the corner of the screen will change. Don't interrupt the setup process!

5. Exit the TV menu by pressing the EXIT or TV button. You can watch TV! If necessary, you can manually arrange channels in the order in which you are accustomed to it, and also remove channels with strong interference or duplicate channels.
Congratulations, you can now use .

The TV user can configure the channels independently. In this regard, it is helped by intuitive interfaces and a simple menu, as well as a Setup Wizard that launches the first time you turn it on. The user can only agree with its help and wait for the process of automatic search and channel setup.

The process can be started automatically or manually.

The setup procedure can become more complicated when working with satellite or cable television.

In most cases, the automatic search copes with its tasks, and after the procedure the user can only remove unnecessary channels from the list.

But sometimes the equipment incorrectly takes into account the scanning range, signal source, etc. Then the procedure can be carried out manually or by selecting new parameters. Of course, if we are talking only about new generations of TVs. In older ones, owners usually only have access to manual mode.

There are no particular advantages in choosing one or another channel search method. The first, automatic, saves time, provides high accuracy, is suitable even for inexperienced users, but can occasionally make mistakes. The second, manual, requires more time and knowledge, but allows you to configure channels in more detail, including in case of poor reception quality.

If none of the methods succeed, you can use the services of a telemaster. The cost of the call will depend on the region of residence, distance from the workshop and its pricing policy. As an alternative, you can consider contacting volunteer organizations that can help with the transition to a new TV format for free.

On old TV, TV channels are adjusted using special knob buttons. For most models, they are located under the switches or near the antenna connector on the back of the panel. You should look for channel frequency regulators under special covers or in drawers.

Setting up a TV of older models is always done manually. Very often, when you turn it on again, there is a need for additional adjustments due to the lack of memory systems. If desired, digital channels can be obtained by connecting the DVA-T2 set-top box.

How to set up a new TV

To connect a new TV to a regular antenna, you must switch to your native language. To do this, the tuned receiver is connected to antenna cable, then long press “OK”, call up the menu, look for the “Country” item, the word LANGUAGE and select RUSSIAN. Now the entire menu will be in Russian.

Automatic channel tuning on TV

How to set up your TV automatically? Almost cable television, as well as analogue, are configured in the same way. It is performed after concluding a service agreement with the provider.

Turn on the receiver, the message “channels not configured” will appear on the monitor. Using the remote control, call up the “Menu”, move the cursor one by one to the lines “Channel settings”, “ Automatic setup” and indicate the type of broadcasting that needs to be configured. Now all that remains is to press ENTER/OK. The television receiver begins to tune in to the channels, scanning the entire frequency range. This takes a few minutes and depends on their number; after the TV ends, it will show all saved TV channels. If it doesn’t work, open and study the instructions that came with the device. It has detailed description setup for this TV.

When a TV operator adds new channels, the settings are made again; for this, the edit line is used. But even after restarting the automatic tuning, all previously recorded channels are saved, and new ones are simply added to free numbers.

If the old receiver needs to be configured in a new way, find the “Delete” entry in the menu program, confirm the action by pressing “OK” and restart the automatic setup.

Manual channel tuning

Manual tuning for television channels is definitely necessary, because the automatic one records some unsatisfactorily. For example, doubles often appear, the image is of poor quality, and there may be no sound. They are removed. But if the channel needs to be saved, you will have to do it manually. This is done like this:

  • in the menu look for “Channel tuning”, “Manual tuning” and press ENTER/OK;
  • select “Program” and assign numbers to the channels;
  • choose a color system: PAL or SECAM, sound: 2.0 (stereo), 5.1, etc.;
  • conduct a “Search” for the channel, if successful, click “Save”.

If necessary, these steps are repeated for each of the TV channels. They must be confirmed by pressing ENTER/OK.

Setting up satellite channels

How to setup satellite channels, if the plate is installed. The cable connects the receiver and the TV, switching it to monitor mode. The remote control for the tuner marks the desired satellite. In the receiver menu, select its scanning. It's easiest to trust it automatic search, which immediately does everything independently, without requiring you to enter the transponder settings manually. Before this, it is advisable to study the instructions that come with the device. It describes in detail how to configure digital channels on a new TV.

There are a lot of such channels, so you need to choose those digital channels that you like best and will watch at least sometimes. We must not forget that when the image deteriorates, the cause may be strong wind and rain, so sometimes the position of the dish is adjusted.

Setting up digital channels

High Definition Television (HDTV) is modern standard transmission of compressed video signals. This technology provides highest quality Pictures. On all modern TVs with DVB-C tuner It became possible to configure digital channels. But such a TV must also have HD viewing capabilities. This new technology is becoming increasingly accessible to a wide range of users. Various companies are appearing that offer setup of digital channels. But you can solve this problem yourself and for free.

Having general knowledge and the manufacturer's instructions, it is easy to set up any TV. First, mark the lines:

  • “Options”, “Automatic setup”, mark the source and press “Start”;
  • hover the cursor over “Digital” and press “Start”;
  • “Search mode” and “Full” option;
  • enter the following data into the fields: frequency (kHz) – 314,000 (314 MHz), modulation – 256 QAM, speed – 6875 kS/s.

Modern TVs are equipped network search, you just need to turn it on and wait. All parameters will be entered automatically. To add new digital TV channels, rescanning is done. After that they appear in the list.

Setting up TV without an antenna

Having high-quality cable Internet, you can watch TV without an antenna. To do this, connect the cable to the TV set-top box. There is another plus: channels from the former CIS countries will become available with excellent quality. Now the vagaries of the weather will not affect the broadcast. There is another positive point: you can watch a missed movie later at any convenient time. can be found in the corresponding section of our website.

Setting up Smart TV makes it possible to watch TV programs directly from the Internet, but to do this you need to have a stable network with a speed of at least 20 Mbit/sec.

Let's look at how to set up a Smart TV. You can connect it in the following ways: connect the router and computer with a cable or use the Wi-Fi service. To ensure simultaneous access to a computer and TV via a 3G modem, a TP-Link TL-MR3420 router is used; it is also suitable for a cable network. Modern Smart TVs are equipped with a special output for connecting to a loyal network; it is connected with a cable to the router. In this case, the router gives the TV an IP address and all other required settings. There is nothing else you need to do, the TV is ready to go.

Some TVs have built-in Wi-Fi or connectivity Wi-Fi adapter, it must be purchased separately. Which adapter to choose is indicated in the TV instructions. One more condition: the router must also have Wi-Fi. This technical possibility does not require running a cable from the router to the TV.

When connecting via wi-fi, go to “ Network connection", and choose the desired network, indicate the Wi-Fi access password. After this, the IP address for the TV device will be automatically assigned.

TV picture adjustment

Setting the TV image is done as follows: in the “Service Menu” find the “Image” line. will appear required parameters: Contrast, Brightness, Sharpness and Color. Use the cursor arrows to change them, selecting the ones most suitable for the eye.

Once having set up the TV on their own, each user will be able to apply this knowledge again; they cannot do without it, because very often new television channels appear on the network or the signal source changes. You have to wait for hours for a technician, when the whole TV setup takes a few minutes, and most importantly, you don’t have to miss your favorite show.